Between the cell and the busbar sits the joint that decides whether a pack behaves like one battery or like a bag of loose cells. Every milliohm of joint resistance turns charge and discharge current into heat at the worst possible place in the current path. An uneven joint pattern pushes parallel paths out of balance. And a tab that fatigues loose in the field looks to the customer exactly like a defective battery, even though the chemistry is fine. Joint quality is a property of a manufacturing process, so it has to be specified and verified like one.
This article describes the three joining methods used for cell-to-busbar interconnects in lithium battery packs, the defects each process tends to produce, and the acceptance evidence an OEM buyer should require before releasing a pack design to production.

Why the tab-to-busbar joint deserves its own specification
The cell tab, the interconnect strip and the busbar together carry the entire pack current. Unlike the cells themselves, the joints are made by a process that runs at high speed and that can drift: electrode wear, fixture alignment and parameter settings all change the result without any visible warning on a finished pack. That is why joint quality cannot be inspected into existence at final assembly – it has to be controlled at the process level.
The engineering consequences show up in three places. Electrically, joint resistance sits in series with the pack current, so it dissipates heat exactly where the current concentrates. Thermally, that localised heat accelerates aging of the cells nearest the worst joint. Structurally, every joint is a potential fatigue site under vibration and thermal cycling. And when several cells share a parallel path, small differences in joint resistance change how current is shared, which feeds directly into the consistency problems that limit pack life.
Field failures caused by joints rarely look like joint failures from the outside. A marginal weld whose resistance grows over service life shows up first as voltage sag under load, which a service technician will read as an aging pack. An intermittently loose tab shows up as random resets or error codes. Both symptoms invite the wrong corrective action – replacing cells or reflashing firmware – when the actual defect is a joining process that drifted. Naming joint acceptance in the specification is what makes this class of failure preventable rather than mysterious.
A 2025 review in Micromachines covers tab-to-busbar interconnections in lithium-ion battery packs and compares the three main welding methods – resistance welding, laser beam welding and ultrasonic welding – in terms of heat input, interfacial metallurgy, electrical resistance, mechanical robustness and manufacturability, with aluminium, copper and nickel-plated copper as the typical material choices.
The three joining methods and what each one buys you
The welding methods review frames the trade-offs, and three points are worth carrying into a supplier discussion:
- Resistance welding is the long-established method for cylindrical-cell packs with nickel-plated steel strips. Two electrodes press the strip against the cell and pass a controlled current pulse through the overlap. It is fast and needs modest equipment, which is why it dominates high-volume cylindrical assembly; its quality depends on electrode condition and consistent energy delivery.
- Ultrasonic welding is a solid-state process: the joint forms through plastic deformation and metallurgical bonding without melting. The review notes that this suppresses porosity and limits aluminium-copper intermetallic growth, but that the process is sensitive to sheet thickness, stack geometry and tool wear. A 2023 study in Materials on ultrasonically welded aluminium/copper joints, which simulated tab-to-busbar interconnects, reported that the plastic deformation concentrated on the aluminium side during welding – a reminder that the softer partner in a dissimilar-metal joint carries most of the process stress.
- Laser beam welding offers precise energy delivery and suits high-speed automated production; the review points out that it demands careful process control in return. Joint strength in laser micro-joints for electric vehicle battery interconnects has itself been the subject of dedicated modelling studies, underlining that weld geometry is a designed parameter, not an accident.
Cell format narrows the choice in practice. Cylindrical cells with nickel-plated steel strip interconnects are the natural territory of resistance welding, and a large cylindrical pack means thousands of near-identical joints – so the challenge shifts from the method itself to consistency across all of them. Pouch and prismatic cells usually present aluminium tabs, and aluminium-to-copper joints are where ultrasonic welding’s solid-state character earns its place; a 2023 study in Materials on ultrasonically welded aluminium/copper joints simulated exactly this tab-to-busbar configuration. Thicker busbars and higher current paths tend to push designs toward laser welding, where the energy can be placed precisely along a defined seam.
The practical point for a buyer is that the joining method should be a named line in the pack specification, not something discovered after the fact. The method drives tooling, cycle time, rework policy and price, and once a design is released around one method, switching later means requalifying the joints from scratch.
| Method | Process character | Strengths | Sensitivities |
|---|---|---|---|
| Resistance welding | Fusion-type joining at the strip overlap via electrode current | Established for cylindrical packs, fast, low capital cost | Energy consistency and electrode wear |
| Ultrasonic welding | Solid-state deformation bonding | Well suited to dissimilar aluminium/copper joints; suppresses porosity and limits intermetallic growth | Sensitive to thickness, stack geometry and tool wear |
| Laser welding | Focused fusion weld | Precise energy delivery, high-speed automation | Requires tight process control; joint strength must be designed |
Sources: Micromachines review of tab-to-busbar welding methods; Materials study on ultrasonically welded Al/Cu joints.
Where weld defects come from and how they are found
Defect modes follow the process physics, so the detection method should match the mechanism rather than rely on one catch-all inspection. The list below reflects typical industry practice rather than a standard-mandated catalogue.
| Defect | Typical cause | How it is detected |
|---|---|---|
| Cold weld, low joint strength | Energy below the process window, worn electrodes, wrong stack-up | Destructive pull or peel test on qualification coupons |
| Weld spatter or burn-through | Excess energy, poor electrode or lens condition | Visual inspection and cross-section sampling |
| Missing weld | Cell or strip misfeed, fixture fault | Visual inspection plus electrical continuity check |
| High or uneven joint resistance | Surface oxides, inconsistent pressure or energy | Per-joint milliohm measurement across the pack |
| Cracking or porosity in fusion welds | Parameter drift, contaminated surfaces | Cross-section sampling; radiographic inspection on critical joints |
| Intermetallic growth at aluminium/copper joints | Uncontrolled heat input over process life | Metallurgical cross-sections on periodic coupons |
Two of these deserve special attention from a buyer. A missing weld is a functional open circuit that will surface at final test – annoying, but contained. A high-resistance joint, by contrast, can pass every electrical test on a cold bench and then overheat under load in the field, so the joint-resistance sampling plan is the single most valuable production control to demand.
What to require from the supplier
Joint acceptance belongs in the pack specification and on the supplier audit list. The requirements below are phrased so each one has a document or a test result attached to it.
| Requirement | Evidence to demand |
|---|---|
| Documented parameter sheet per cell type and interconnect material | A controlled process sheet with energy settings, pressure or clamping, and electrode or optics condition rules |
| Qualification coupons at setup and per shift or lot | Pull or peel test results against a defined minimum force, with the number of coupons stated |
| Joint resistance sampling plan | Milliohm values with upper limits, sample size and acceptance rules, using defined probe points |
| Visual inspection rules | Full inspection for safety-critical joints and a sampling plan for the remainder, with defect photos as reference |
| Traceability | Weld and coupon data linked to pack serial numbers |
| Rework rules | Whether a failed coupon allows re-welding or forces scrap, stated in advance |

How large a sample to pull and how to judge the spread of results is a measurement and statistics question; the NIST/SEMATECH e-Handbook chapter on process summarises the underlying reasoning, which can be applied to coupon counts and resistance limits.
Because joint quality is process-dependent, the specification should also define when requalification is required. Typical triggers include a new cell or strip supplier, a fixture or electrode change, a parameter sheet revision, or a production line move. Each trigger resets the coupon clock: the first packs produced after the change carry fresh destructive testing before they ship. Electrode maintenance deserves its own rule as well – dressing and replacement intervals tied to coupon results rather than to a fixed calendar, since electrode wear shows up in the coupons long before it shows up in pack test data. None of this is exotic; it is the ordinary discipline of a controlled process, and a supplier who already runs it will have the records on hand.
How joint acceptance fits the rest of pack qualification
Safety standards for finished packs – IEC 62619 for industrial applications and IEC 62133-2 for portable sealed packs – verify the assembled product. A marginal joint can pass those tests on a cold bench and still fail mechanically after months of vibration or thermal cycling. That is why joint-level acceptance belongs upstream of final certification: it is verified at the process level, while the standards verify the finished design.
In practice, joint acceptance connects to three other parts of a sourcing programme. Incoming inspection catches cell-level problems before they reach the welder – our incoming inspection checklist covers the pack-level version. The interconnect method and its acceptance criteria should be named in the RFQ itself, as our RFQ checklist recommends, because the choice of welding method affects tooling, cycle time and price. And when you evaluate an assembly partner, the weld process is a fair audit target alongside the rest of production – the same applies whether the partner assembles 18650-format packs or larger modules, as described in our overview of 21700 pack assembly suppliers.
If you want joint-level acceptance criteria reviewed before a production release, or need a second opinion on an assembly process window, contact our engineering team with the cell format and interconnect material involved.

